A few days ago, my device Cubox-i4pro started to reboot spontaneously. I tried reinstalling the operating system Debian 10 Buster (cli) on the microsd card, but it doesn’t help. I tried to use different microsd’s with no success. Serial Console Output:
U-Boot SPL 2018.01-02296-g457cdd60c3 (May 17 2018 - 22:59:22)
Trying to boot from MMC1
U-Boot 2018.01-02296-g457cdd60c3 (May 17 2018 - 22:59:22 +0200), Build: jenkins-u-boot-imx6-variant=sdhc-2
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 36C
Reset cause: POR
Board: MX6 Cubox-i
Watchdog enabled
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1…
Found U-Boot script /boot/boot.scr
2925 bytes read in 108 ms (26.4 KiB/s)
Executing script at 12000000
7149960 bytes read in 416 ms (16.4 MiB/s)
41863 bytes read in 128 ms (319.3 KiB/s)
12126588 bytes read in 693 ms (16.7 MiB/s)
Booting Debian 4.9.150-imx6-sr from mmc 0:1…
Flattened Device Tree blob at 18000000
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800d386
Starting kernel …
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.150-imx6-sr (abuild@hummingboard1) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP Sun Sep 8 01:52:51 UTC 2019
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: SolidRun Cubox-i Dual/Quad
[ 0.000000] Reserved memory: created CMA memory pool at 0x70000000, size 256 MiB
[ 0.000000] OF: reserved mem: initialized node linux,gpu, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x3e000000, size 32 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 14 pages/cpu @ecda0000 s26764 r8192 d22388 u57344
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: console=ttymxc0,115200 log_level=7 net.ifnames=0
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1755448K/2097152K available (9216K kernel code, 420K rwdata, 3096K rodata, 1024K init, 532K bss, 46792K reserved, 294912K cma-reserved, 1048576K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0a00000 (10208 kB)
[ 0.000000] .init : 0xc0e00000 - 0xc0f00000 (1024 kB)
[ 0.000000] .data : 0xc0f00000 - 0xc0f690c0 ( 421 kB)
[ 0.000000] .bss : 0xc0f690c0 - 0xc0fee2e0 ( 533 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L2C-310 errata 752271 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
[ 0.000000] Switching to timer-based delay loop, resolution 333ns
[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[ 0.000025] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[ 0.001236] Console: colour dummy device 80x30
[ 0.001262] Calibrating delay loop (skipped), value calculated using timer frequency… 6.00 BogoMIPS (lpj=3000)
[ 0.001275] pid_max: default: 32768 minimum: 301
[ 0.001377] Security Framework initialized
[ 0.001389] SELinux: Initializing.
[ 0.001482] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001493] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002321] CPU: Testing write buffer coherency: ok
[ 0.002347] CPU0: Spectre v2: using BPIALL workaround
[ 0.002726] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002792] Setting up static identity map for 0x10100000 - 0x10100058
[ 0.005157] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.005164] CPU1: Spectre v2: using BPIALL workaround
[ 0.006137] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.006143] CPU2: Spectre v2: using BPIALL workaround
[ 0.007102] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.007107] CPU3: Spectre v2: using BPIALL workaround
[ 0.007212] Brought up 4 CPUs
[ 0.007224] SMP: Total of 4 processors activated (24.00 BogoMIPS).
[ 0.007231] CPU: All CPU(s) started in SVC mode.
[ 0.008210] devtmpfs: initialized
[ 0.033537] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 512590
[ 0.034211] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.034624] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.034649] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.034888] atomic64_test: passed
[ 0.034898] pinctrl core: initialized pinctrl subsystem
[ 0.035964] NET: Registered protocol family 16
[ 0.042983] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.046585] cpuidle: using governor menu
[ 0.046716] CPU identified as i.MX6Q, silicon rev 1.5
[ 0.066933] No ATAGs?
[ 0.066966] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.066975] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.067502] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.068930] imx-gpc 20dc000.gpc: no fsl,ldo-bypass found!
[ 0.069046] imx-gpc 20dc000.gpc: Registered imx-gpc
[ 0.099420] mxs-dma 110000.dma-apbh: initialized
[ 0.101102] vcc_3v3: supplied by v_5v0
[ 0.101372] v_usb2: supplied by v_5v0
[ 0.101805] v_usb1: supplied by v_5v0
[ 0.102494] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX
[ 0.607240] console [ttymxc0] enabled
[ 0.611998] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 68, base_baud = 5000000) is a IMX
[ 0.620868] serial serial0: tty port ttymxc3 registered
[ 0.626466] vgaarb: loaded
[ 0.629927] SCSI subsystem initialized
[ 0.634208] usbcore: registered new interface driver usbfs
[ 0.639777] usbcore: registered new interface driver hub
[ 0.645187] usbcore: registered new device driver usb
[ 0.650408] 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
[ 0.658300] 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator
[ 0.666668] imx-i2c 21a4000.i2c: stop-delay=0, inter-byte-delay=0
[ 0.673105] i2c i2c-1: IMX I2C adapter registered
[ 0.677842] i2c i2c-1: can’t use DMA, using PIO instead.
[ 0.683455] imx-i2c 21a8000.i2c: stop-delay=0, inter-byte-delay=0
[ 0.689872] i2c i2c-2: IMX I2C adapter registered
[ 0.694619] i2c i2c-2: can’t use DMA, using PIO instead.
[ 0.700066] media: Linux media interface: v0.10
[ 0.704669] Linux video capture interface: v2.00
[ 0.709373] pps_core: LinuxPPS API ver. 1 registered
[ 0.714357] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.723519] PTP clock support registered
[ 0.730615] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.741590] imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.749922] MIPI CSI2 driver module loaded
[ 0.754155] Advanced Linux Sound Architecture Driver Initialized.
[ 0.761196] NetLabel: Initializing
[ 0.764624] NetLabel: domain hash size = 128
[ 0.768993] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.774028] NetLabel: unlabeled traffic allowed by default
[ 0.779968] clocksource: Switched to clocksource mxc_timer1
[ 0.785730] VFS: Disk quotas dquot_6.6.0
[ 0.789740] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.807891] NET: Registered protocol family 2
[ 0.813020] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.820181] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.826781] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.833295] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.839283] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.845985] NET: Registered protocol family 1
[ 0.850938] RPC: Registered named UNIX socket transport module.
[ 0.856905] RPC: Registered udp transport module.
[ 0.861636] RPC: Registered tcp transport module.
[ 0.866366] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.873169] Trying to unpack rootfs image as initramfs…
[ 1.819803] Freeing initrd memory: 11844K
[ 1.824419] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 1.834021] Bus freq driver module loaded
[ 1.839129] audit: initializing netlink subsys (disabled)
[ 1.844649] audit: type=2000 audit(1.283:1): initialized
[ 1.851067] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 1.865748] NFS: Registering the id_resolver key type
[ 1.870874] Key type id_resolver registered
[ 1.875089] Key type id_legacy registered
[ 1.879131] nfs4filelayout_init: NFSv4 File Layout Driver Registering…
[ 1.886131] fuse init (API version 7.26)
[ 5.331012] NET: Registered protocol family 38
[ 5.335547] bounce: pool size: 64 pages
[ 5.339493] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 5.347080] io scheduler noop registered
[ 5.351034] io scheduler deadline registered
[ 5.355621] io scheduler cfq registered (default)
[ 5.362485] 20e0000.hdmi_video supply HDMI not found, using dummy regulator
[ 5.369983] mxc_sdc_fb fb@0: assigned reserved memory node linux,gpu
[ 5.376374] mxc_sdc_fb fb@0: IPU Successfully registered fbdev to custom memory-region
[ 5.384440] mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
[ 5.392273] fbcvt: 1920x1080@60: CVT Name - 2.073M9
[ 5.397278] mxc_sdc_fb fb@0: registered mxc display driver hdmi IPU1_DISP0
[ 5.404181] mxc_sdc_fb fb@0: registered mxc display driver hdmi
[ 5.554759] mxc_sdc_fb fb@0: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36 pixclock=148500000 Hz
[ 5.554883] imx-ipuv3 2400000.ipu: try ipu internal clk
[ 5.562017] imx-ipuv3 2400000.ipu: disp=0, pixel_clk=148500000 148500000 parent=148500000 div=1
[ 5.562026] find_field: [0] = 0x7ff, max=23
[ 5.562032] find_field: [1] = 0xfff, max=23
[ 5.562037] find_field: [2] = 0x17ff, max=23
[ 5.562040] find_field: [0] = 0x820, max=29
[ 5.562085] imx-ipuv3 2400000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 5.612158] mxc_sdc_fb fb@0: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36 pixclock=148500000 Hz
[ 5.612256] imx-ipuv3 2400000.ipu: try ipu internal clk
[ 5.619004] imx-ipuv3 2400000.ipu: disp=0, pixel_clk=148500000 148500000 parent=148500000 div=1
[ 5.659212] Console: switching to colour frame buffer device 240x67
[ 5.734148] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 5.744204] [drm] Initialized
[ 5.747660] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 5.768314] brd: module loaded
[ 5.771559] loop: module loaded
[ 5.775837] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104, using 00000044
[ 5.783535] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using 00000000
[ 5.791046] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9, using 00002000
[ 5.798728] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000
[ 5.811024] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled
[ 5.818048] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 5.826868] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[ 5.838542] scsi host0: ahci-imx
[ 5.842156] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 75
[ 5.851185] libphy: Fixed MDIO Bus: probed
[ 5.856208] 2188000.ethernet supply phy not found, using dummy regulator
[ 5.866555] pps pps0: new PPS source ptp0
[ 5.890146] libphy: fec_enet_mii_bus: probed
[ 5.895105] fec 2188000.ethernet eth0: registered PHC device 0
[ 5.901507] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 5.908065] ehci-pci: EHCI PCI platform driver
[ 5.912603] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 5.918818] ohci-pci: OHCI PCI platform driver
[ 5.923333] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.929922] usbcore: registered new interface driver usb-storage
[ 5.936003] usbcore: registered new interface driver ums-usbat
[ 5.941993] usbcore: registered new interface driver usbserial
[ 5.947889] usbcore: registered new interface driver usbserial_generic
[ 5.954478] usbserial: USB Serial support registered for generic
[ 5.961669] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[ 5.969775] setup_reset_gpios:-2, flags 0
[ 5.978690] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 5.983878] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 6.000006] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 6.005603] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.012438] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.019690] usb usb1: Product: EHCI Host Controller
[ 6.024595] usb usb1: Manufacturer: Linux 4.9.150-imx6-sr ehci_hcd
[ 6.030802] usb usb1: SerialNumber: ci_hdrc.0
[ 6.035900] hub 1-0:1.0: USB hub found
[ 6.039715] hub 1-0:1.0: 1 port detected
[ 6.044434] setup_reset_gpios:-2, flags 0
[ 6.051891] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 6.057094] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 6.073003] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 6.078608] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.085440] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.092691] usb usb2: Product: EHCI Host Controller
[ 6.097596] usb usb2: Manufacturer: Linux 4.9.150-imx6-sr ehci_hcd
[ 6.103799] usb usb2: SerialNumber: ci_hdrc.1
[ 6.108837] hub 2-0:1.0: USB hub found
[ 6.112650] hub 2-0:1.0: 1 port detected
[ 6.117606] mousedev: PS/2 mouse device common for all mice
[ 6.124513] rtc-pcf8523 2-0068: RTC reports battery is low
[ 6.130032] rtc-pcf8523 2-0068: starting calibration at 12.5 pf
[ 6.141114] rtc-pcf8523 2-0068: rtc core: registered rtc-pcf8523 as rtc0
[ 6.148565] check_alarm_past: alarm in the past
[ 6.153350] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 6.158610] ata1: SATA link down (SStatus 0 SControl 300)
[ 6.158646] ahci-imx 2200000.sata: no device found, disabling link.
[ 6.158652] ahci-imx 2200000.sata: pass ahci_imx…hotplug=1 to enable hotplug
[ 6.181063] i2c /dev entries driver
[ 6.185025] IR Sharp protocol handler initialized
[ 6.189755] IR XMP protocol handler initialized
[ 6.195783] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 6.202122] device-mapper: uevent: version 1.0.3
[ 6.207128] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 6.216573] sdhci: Secure Digital Host Controller Interface driver
[ 6.222793] sdhci: Copyright(c) Pierre Ossman
[ 6.227183] sdhci-pltfm: SDHCI platform and OF driver helper
[ 6.234241] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq
[ 6.479002] mmc1: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 6.488831] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode
[ 6.501123] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
[ 6.527746] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 6.534975] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 6.540669] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[ 6.554135] mxc_vpu 2040000.vpu_fsl: assigned reserved memory node linux,gpu
[ 6.561235] mxc_vpu 2040000.vpu_fsl: VPU Successfully registered to custom memory-region
[ 6.569403] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 6.575111] mxc_vpu 2040000.vpu_fsl: VPU initialized
[ 6.579041] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 6.582123] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 6.591602] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
[ 6.599812] HDMI-CEC initialized
[ 6.604073] caam 2100000.caam: ERA source: CAAMVID.
[ 6.609017] caam 2100000.caam: AXI pipeline throttling enabled.
[ 6.611015] random: fast init done
[ 6.619211] caam 2100000.caam: Entropy delay = 3200
[ 6.635627] mmc0: host does not support reading read-only switch, assuming write-enable
[ 6.653094] mmc0: new high speed SDHC card at address b368
[ 6.661679] mmc1: new high speed SDIO card at address 0001
[ 6.668268] mmcblk0: mmc0:b368 NCard 7.48 GiB
[ 6.677971] mmcblk0: p1
[ 6.684900] caam 2100000.caam: Instantiated RNG4 SH0
[ 6.745661] caam 2100000.caam: Instantiated RNG4 SH1
[ 6.750656] caam 2100000.caam: device ID = 0x0a16010000000000 (Era 4)
[ 6.757120] caam 2100000.caam: job rings = 2, qi = 0
[ 6.769756] alg: No test for authenc(hmac(sha224),ecb(cipher_null)) (authenc-hmac-sha224-ecb-cipher_null-caam)
[ 6.779919] alg: No test for authenc(hmac(sha256),ecb(cipher_null)) (authenc-hmac-sha256-ecb-cipher_null-caam)
[ 6.790115] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam)
[ 6.798390] alg: No test for echainiv(authenc(hmac(md5),cbc(aes))) (echainiv-authenc-hmac-md5-cbc-aes-caam)
[ 6.810160] alg: No test for echainiv(authenc(hmac(sha1),cbc(aes))) (echainiv-authenc-hmac-sha1-cbc-aes-caam)
[ 6.820236] alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam)
[ 6.829046] alg: No test for echainiv(authenc(hmac(sha224),cbc(aes))) (echainiv-authenc-hmac-sha224-cbc-aes-caam)
[ 6.841167] alg: No test for echainiv(authenc(hmac(sha256),cbc(aes))) (echainiv-authenc-hmac-sha256-cbc-aes-caam)
[ 6.851581] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam)
[ 6.860709] alg: No test for echainiv(authenc(hmac(md5),cbc(des3_ede))) (echainiv-authenc-hmac-md5-cbc-des3_ede-caam)
[ 6.871897] alg: No test for echainiv(authenc(hmac(sha1),cbc(des3_ede))) (echainiv-authenc-hmac-sha1-cbc-des3_ede-caam)
[ 6.883322] alg: No test for echainiv(authenc(hmac(sha224),cbc(des3_ede))) (echainiv-authenc-hmac-sha224-cbc-des3_ede-caam)
[ 6.895027] alg: No test for echainiv(authenc(hmac(sha256),cbc(des3_ede))) (echainiv-authenc-hmac-sha256-cbc-des3_ede-caam)
[ 6.906307] alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam)
[ 6.914563] alg: No test for echainiv(authenc(hmac(md5),cbc(des))) (echainiv-authenc-hmac-md5-cbc-des-caam)
[ 6.924847] alg: No test for echainiv(authenc(hmac(sha1),cbc(des))) (echainiv-authenc-hmac-sha1-cbc-des-caam)
[ 6.935405] alg: No test for echainiv(authenc(hmac(sha224),cbc(des))) (echainiv-authenc-hmac-sha224-cbc-des-caam)
[ 6.946242] alg: No test for echainiv(authenc(hmac(sha256),cbc(des))) (echainiv-authenc-hmac-sha256-cbc-des-caam)
[ 6.956657] alg: No test for authenc(hmac(md5),rfc3686(ctr(aes))) (authenc-hmac-md5-rfc3686-ctr-aes-caam)
[ 6.966395] alg: No test for seqiv(authenc(hmac(md5),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-md5-rfc3686-ctr-aes-caam)
[ 6.977371] alg: No test for seqiv(authenc(hmac(sha1),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha1-rfc3686-ctr-aes-caam)
[ 6.988411] alg: No test for authenc(hmac(sha224),rfc3686(ctr(aes))) (authenc-hmac-sha224-rfc3686-ctr-aes-caam)
[ 6.998687] alg: No test for seqiv(authenc(hmac(sha224),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha224-rfc3686-ctr-aes-caam)
[ 7.010180] alg: No test for seqiv(authenc(hmac(sha256),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha256-rfc3686-ctr-aes-caam)
[ 7.021449] caam algorithms registered in /proc/crypto
[ 7.043095] caam_jr 2101000.jr0: registering rng-caam
[ 7.048865] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.054583] usbcore: registered new interface driver usbhid
[ 7.060183] usbhid: USB HID core driver
[ 7.123365] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517
[ 7.132666] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered
[ 7.139238] imx-spdif sound-spdif: snd_soc_register_card failed: -517
[ 7.192263] imx-audio-hdmi sound-hdmi: hdmi-hifi.0 <-> soc:hdmi_audio@00120000 mapping ok
[ 7.202388] Initializing XFRM netlink socket
[ 7.207238] NET: Registered protocol family 10
[ 7.212719] mip6: Mobile IPv6
[ 7.215724] NET: Registered protocol family 17
[ 7.220249] 8021q: 802.1Q VLAN Support v1.8
[ 7.224501] Key type dns_resolver registered
[ 7.230869] cpu cpu0: Registered imx6q-cpufreq
[ 7.236340] registered taskstats version 1
[ 7.283038] Key type big_key registered
[ 7.299735] imx_thermal 2000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C
[ 7.354809] fsl-spdif-dai 2004000.spdif: Unbalanced pm_runtime_enable!
[ 7.361407] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517
[ 7.368311] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered
[ 7.374867] imx-spdif sound-spdif: snd_soc_register_card failed: -517
[ 7.381907] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
[ 7.393183] rtc-pcf8523 2-0068: hctosys: unable to read the hardware clock
[ 7.400694] ALSA device list:
[ 7.403693] #0: imx-hdmi-soc
[ 7.421414] Freeing unused kernel memory: 1024K
[ 7.444498] fsl-spdif-dai 2004000.spdif: Unbalanced pm_runtime_enable!
[ 7.451193] fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517
[ 7.458390] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered
[ 7.465001] imx-spdif sound-spdif: snd_soc_register_card failed: -517
Loading, please wait…
Starting version 241