# Ubuntu Image fails to boot on Clearfog LX2K **URL:** \ **Category:** NXP LX2160\ **Tags:** NXP-LX2160\ **Created:** [June 9, 2021, 3:29pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71 "2021-06-09T15:29:18Z")\ **Posts on this page:** 17\ **Page:** 1
**Author:** ![blien](https://avatars.discourse-cdn.com/v4/letter/b/ecae2f/32.png) [@blien](https://community.solid-run.com/u/blien)\ **Post date:** [June 9, 2021, 3:29pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/1 "2021-06-09T15:29:18Z")
I downloaded the lx2160acex7\_2000\_700\_3200\_8\_5\_2-2fff64e.img from solid run website. I know my RAM is 3200 which should match the listed image. I cannot get this image to boot and get the error as seen in below console log. Ultimately, I am looking to get VxWorks running on this board, but when that didn’t work I wanted to verify the board with a known working image. NOTICE: BL2: v1.5(release):LSDK-20.12-8-gcab7d26 NOTICE: BL2: Built : 17:36:59, Feb 18 2021 NOTICE: UDIMM KHX3200C20S4/16GX NOTICE: DDR4 UDIMM with 2-rank 64-bit bus (x8) NOTICE: 32 GB DDR4, 64-bit, CL=20, ECC off, 256B, CS0+CS1 NOTICE: BL2: Booting BL31 NOTICE: BL31: v1.5(release):LSDK-20.12-8-gcab7d26 NOTICE: BL31: Built : 17:36:59, Feb 18 2021 NOTICE: Welcome to LX2160 BL31 Phase U-Boot 2020.04-00026-g2ad74828 (Feb 18 2021 - 17:36:55 +0000) SoC: LX2160ACE Rev2.0 (0x87360020) Clock Configuration: CPU0(A72):2000 MHz CPU1(A72):2000 MHz CPU2(A72):2000 MHz CPU3(A72):2000 MHz CPU4(A72):2000 MHz CPU5(A72):2000 MHz CPU6(A72):2000 MHz CPU7(A72):2000 MHz CPU8(A72):2000 MHz CPU9(A72):2000 MHz CPU10(A72):2000 MHz CPU11(A72):2000 MHz CPU12(A72):2000 MHz CPU13(A72):2000 MHz CPU14(A72):2000 MHz CPU15(A72):2000 MHz Bus: 700 MHz DDR: 3200 MT/s Reset Configuration Word (RCW): 00000000: 50838338 24500050 00000000 00000000 00000010: 00000000 0e010000 00000000 00000000 00000020: 0fc001a0 00002580 00000000 08000086 00000030: 09240000 00000001 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 08a80001 00151020 Model: SolidRun LX2160ACEX7 COM express type 7 based board Board: LX2160ACE Rev2.0-CEX7, SD SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 100MHz SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz DRAM: 31.9 GiB DDR 31.9 GiB (DDR4, 64-bit, CL=20, ECC off) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 WDT: Started with servicing (30s timeout) Using SERDES1 Protocol: 8 (0x8) Using SERDES2 Protocol: 5 (0x5) Using SERDES3 Protocol: 2 (0x2) MMC: FSL\_SDHC: 0, FSL\_SDHC: 1 Loading Environment from MMC… OK In: serial\_pl01x Out: serial\_pl01x Err: serial\_pl01x Net: Setting up retimer channels 1..4 as 10Gbps EEPROM: TlvInfo v1 len=114 PCIe1: pcie@3400000 disabled PCIe2: pcie@3500000 disabled PCIe3: pcie@3600000 Root Complex: no link PCIe4: pcie@3700000 disabled PCIe5: pcie@3800000 Root Complex: no link PCIe6: pcie@3900000 disabled DPMAC3@xgmii, DPMAC4@xgmii Warning: DPMAC4@xgmii (eth1) using random MAC address - 26:64:7d:6c:69:ef , DPMAC5@xgmii … … … =\> run sd\_bootcmd Trying load from sd card.. Device: FSL\_SDHC Manufacturer ID: 3 OEM: 5344 Name: SC32G Bus Speed: 50000000 Mode: SD High Speed (50MHz) Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 29.7 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes MMC read: dev # 0, block # 32768, count 81920 … 81920 blocks read: OK ## Loading kernel from FIT Image at a0000000 … Using ‘lx2160acex7’ configuration Trying ‘kernel’ kernel subimage Description: ARM64 Kernel Created: 2021-02-18 17:40:32 UTC Type: Kernel Image Compression: gzip compressed Data Start: 0xa00000d0 Data Size: 14167789 Bytes = 13.5 MiB Architecture: AArch64 OS: Linux Load Address: 0x80080000 Entry Point: 0x80080000 Hash algo: crc32 Hash value: ffc2c7a7 Verifying Hash Integrity … crc32+ OK ## Loading ramdisk from FIT Image at a0000000 … Using ‘lx2160acex7’ configuration Trying ‘initrd’ ramdisk subimage Description: initrd for arm64 Created: 2021-02-18 17:40:32 UTC Type: RAMDisk Image Compression: uncompressed Data Start: 0xa0d830a0 Data Size: 11535243 Bytes = 11 MiB Architecture: AArch64 OS: Linux Load Address: 0x00000000 Entry Point: 0x00000000 Hash algo: crc32 Hash value: c150f71f Verifying Hash Integrity … crc32+ OK ## Loading fdt from FIT Image at a0000000 … Using ‘lx2160acex7’ configuration Trying ‘lx2160acex7-dtb’ fdt subimage Description: lx2160acex7-dtb Created: 2021-02-18 17:40:32 UTC Type: Flat Device Tree Compression: uncompressed Data Start: 0xa1883510 Data Size: 28471 Bytes = 27.8 KiB Architecture: AArch64 Load Address: 0x90000000 Hash algo: crc32 Hash value: 372b1e5b Verifying Hash Integrity … crc32+ OK Loading fdt from 0xa1883510 to 0x90000000 Booting using the fdt blob at 0x90000000 Uncompressing Kernel Image Loading Device Tree to 000000009fff6000, end 000000009fffff36 … OK Releasing fan controller full speed gpio fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel … … … [4.833476] No soundcards found. [4.843496] mmc1: new HS400 MMC card at address 0001 [4.848765] mmcblk1: mmc1:0001 DF4064 58.2 GiB [4.853355] hub 3-1.3:1.0: USB hub found [4.853438] mmcblk1boot0: mmc1:0001 DF4064 partition 1 4.00 MiB [4.857310] hub 3-1.3:1.0: 4 ports detected [4.863334] mmcblk1boot1: mmc1:0001 DF4064 partition 2 4.00 MiB [4.873326] mmcblk1rpmb: mmc1:0001 DF4064 partition 3 4.00 MiB, chardev (508:0) [4.917833] RAMDISK: gzip image found at block 0 [5.233387] EXT4-fs (ram0): mounted filesystem with ordered data mode. Opts: (null) [5.241062] VFS: Mounted root (ext4 filesystem) on device 1:0. Bad inittab entry at line 5 can’t open /dev/si: No such file or directory can’t open /dev/~~: No such file or directory can’t open /dev/l0: No such file or directory can’t open /dev/l1: No such file or directory can’t open /dev/l2: No such file or directory can’t open /dev/l3: No such file or directory can’t open /dev/l4: No such file or directory can’t open /dev/l5: No such file or directory can’t open /dev/l6: No such file or directory It wouldn’t allow me to post entire console output. ---
**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\ **Post date:** [June 10, 2021, 5:40am UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/2 "2021-06-10T05:40:59Z")
I see that you are running sd\_bootcmd manually. Does the image boot if you just run `boot` or let u-boot continue the boot process automatically? ---
**Author:** ![blien](https://avatars.discourse-cdn.com/v4/letter/b/ecae2f/32.png) [@blien](https://community.solid-run.com/u/blien)\ **Post date:** [June 14, 2021, 2:26pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/3 "2021-06-14T14:26:37Z")
NOTICE: BL2: v1.5(release):LSDK-20.12-8-gcab7d26 NOTICE: BL2: Built : 17:36:59, Feb 18 2021 NOTICE: UDIMM KHX3200C20S4/16GX NOTICE: DDR4 UDIMM with 2-rank 64-bit bus (x8) NOTICE: 32 GB DDR4, 64-bit, CL=20, ECC off, 256B, CS0+CS1 NOTICE: BL2: Booting BL31 NOTICE: BL31: v1.5(release):LSDK-20.12-8-gcab7d26 NOTICE: BL31: Built : 17:36:59, Feb 18 2021 NOTICE: Welcome to LX2160 BL31 Phase U-Boot 2020.04-00026-g2ad74828 (Feb 18 2021 - 17:36:55 +0000) SoC: LX2160ACE Rev2.0 (0x87360020) Clock Configuration: CPU0(A72):2000 MHz CPU1(A72):2000 MHz CPU2(A72):2000 MHz CPU3(A72):2000 MHz CPU4(A72):2000 MHz CPU5(A72):2000 MHz CPU6(A72):2000 MHz CPU7(A72):2000 MHz CPU8(A72):2000 MHz CPU9(A72):2000 MHz CPU10(A72):2000 MHz CPU11(A72):2000 MHz CPU12(A72):2000 MHz CPU13(A72):2000 MHz CPU14(A72):2000 MHz CPU15(A72):2000 MHz Bus: 700 MHz DDR: 3200 MT/s Reset Configuration Word (RCW): 00000000: 50838338 24500050 00000000 00000000 00000010: 00000000 0e010000 00000000 00000000 00000020: 0fc001a0 00002580 00000000 08000086 00000030: 09240000 00000001 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 08a80001 00151020 Model: SolidRun LX2160ACEX7 COM express type 7 based board Board: LX2160ACE Rev2.0-CEX7, SD SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 100MHz SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz DRAM: 31.9 GiB DDR 31.9 GiB (DDR4, 64-bit, CL=20, ECC off) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 WDT: Started with servicing (30s timeout) Using SERDES1 Protocol: 8 (0x8) Using SERDES2 Protocol: 5 (0x5) Using SERDES3 Protocol: 2 (0x2) MMC: FSL\_SDHC: 0, FSL\_SDHC: 1 Loading Environment from MMC… \*\*\* Warning - bad CRC, using default environment In: serial\_pl01x Out: serial\_pl01x Err: serial\_pl01x Net: Setting up retimer channels 1…4 as 10Gbps EEPROM: TlvInfo v1 len=114 PCIe1: pcie@3400000 disabled PCIe2: pcie@3500000 disabled PCIe3: pcie@3600000 Root Complex: no link PCIe4: pcie@3700000 disabled PCIe5: pcie@3800000 Root Complex: no link PCIe6: pcie@3900000 disabled DPMAC3@xgmii, DPMAC4@xgmii Warning: DPMAC4@xgmii (eth1) using random MAC address - 06:e1:16:6b:69:e1 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth2) using random MAC address - 0e:03:b7:e4:bb:4a , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth3) using random MAC address - 06:74:1c:88:bc:58 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth4) using random MAC address - ba:c9:6b:48:1d:38 , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth5) using random MAC address - 0a:9f:ab:f8:49:b9 , DPMAC9@xgmii Warning: DPMAC9@xgmii (eth6) using random MAC address - 3e:a8:ff:7c:d6:79 , DPMAC10@xgmii Warning: DPMAC10@xgmii (eth7) using random MAC address - 2a:a5:52:fa:a1:46 , DPMAC17@rgmii-id [PRIME] Warning: DPMAC17@rgmii-id (eth8) using random MAC address - fa:05:0c:36:2e:8f , DPMAC18@rgmii-id Warning: DPMAC18@rgmii-id (eth9) using random MAC address - fa:35:2d:d1:17:23 MMC read: dev # 0, block # 20480, count 4608 … 4608 blocks read: OK MMC read: dev # 0, block # 28672, count 2048 … 2048 blocks read: OK crc32+ fsl-mc: Booting Management Complex … SUCCESS fsl-mc: Management Complex booted (version: 10.24.0, boot status: 0x1) Hit any key to stop autoboot: 0 Device: FSL\_SDHC Manufacturer ID: 1b OEM: 534d Name: EB1QT Bus Speed: 50000000 Mode: SD High Speed (50MHz) Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 29.8 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes MMC read: dev # 0, block # 26624, count 2048 … 2048 blocks read: OK starting USB… Bus usb3@3100000: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 Bus usb3@3110000: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus usb3@3100000 for devices… 1 USB Device(s) found scanning bus usb3@3110000 for devices… 4 USB Device(s) found scanning usb for storage devices… 0 Storage Device(s) found Device 0: unknown device switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1… switch to partitions #0, OK mmc1(part 0) is current device \*\* No partition table - mmc 1 \*\* scanning bus for devices… SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Target spinup took 0 ms. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Device 0: (0:0) Vendor: ATA Prod.: CT1000MX500SSD1 Rev: M3CR Type: Hard Disk Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Device 0: (0:0) Vendor: ATA Prod.: CT1000MX500SSD1 Rev: M3CR Type: Hard Disk Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) … is now current device \*\* No partition table - scsi 0 \*\* Device 0: unknown device BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.4.37 (1024 ms) \*\*\* ERROR: `serverip' not set Cannot autoload with TFTPGET BOOTP broadcast 1 DHCP client bound to address 192.168.4.37 (3 ms) *** ERROR: `serverip’ not set Cannot autoload with TFTPGET Trying load from sd card… Device: FSL\_SDHC Manufacturer ID: 45 OEM: 100 Name: DF406 Bus Speed: 50000000 Mode: MMC High Speed (52MHz) Rd Block Len: 512 MMC version 5.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 KiB HC WP Group Size: 8 MiB User Capacity: 58.2 GiB WRREL Boot Capacity: 4 MiB ENH RPMB Capacity: 4 MiB ENH MMC read: dev # 1, block # 32768, count 81920 … 81920 blocks read: OK Wrong Image Format for bootm command ERROR: can’t get kernel image! =\> ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [August 28, 2024, 4:41pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/4 "2024-08-28T16:41:53Z")
> [@blien](#): > > run sd\_bootcmd I have also a error. ```auto NOTICE: DDR PMU Hardware version-0x1210 NOTICE: DDR PMU Firmware vision-0x1001 (vA-2019.04) NOTICE: DDR4 UDIMM with 1-rank 64-bit bus (x8) NOTICE: 8 GB DDR4, 64-bit, CL=22, ECC off NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.4(release):LSDK-21.08-8-gc330ead97 NOTICE: BL31: Built : 18:02:55, Jul 4 2024 NOTICE: Welcome to lx2160acex7 BL31 Phase U-Boot 2021.04-00046-g32b5d1ea333 (Jul 04 2024 - 18:02:51 +0000) SoC: LX2162AE Rev2.0 (0x87361820) Clock Configuration: CPU0(A72):2000 MHz CPU1(A72):2000 MHz CPU2(A72):2000 MHz CPU3(A72):2000 MHz CPU4(A72):2000 MHz CPU5(A72):2000 MHz CPU6(A72):2000 MHz CPU7(A72):2000 MHz CPU8(A72):2000 MHz CPU9(A72):2000 MHz CPU10(A72):2000 MHz CPU11(A72):2000 MHz CPU12(A72):2000 MHz CPU13(A72):2000 MHz CPU14(A72):2000 MHz CPU15(A72):2000 MHz Bus: 700 MHz DDR: 3200 MT/s Reset Configuration Word (RCW): 00000000: 50838338 24500050 00000000 00000000 00000010: 00000000 0e010000 00000000 00000000 00000020: 10c001a0 00002580 00000000 08000086 00000030: 09240000 00000001 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027005 00000000 00000070: 01320034 00153022 Model: SolidRun LX2162A Clearfog Board: LX2162AE Rev2.0-CEX7, eMMC SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 100MHz SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz DRAM: 7.9 GiB DDR 7.9 GiB (DDR4, 64-bit, CL=22, ECC off) PCA: failed to select bus 0 channel 8 dev_get_priv: null device dev_get_priv: null device Using SERDES1 Protocol: 18 (0x12) Using SERDES2 Protocol: 9 (0x9) Using SERDES3 Protocol: 0 (0x0) SERDES3[PRTCL] = 0x0 is not valid PCIe1: pcie@3400000 disabled PCIe2: pcie@3500000 disabled PCIe5: pcie@3800000 disabled PCIe6: pcie@3900000 disabled WDT: Started with servicing (30s timeout) MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment EEPROM: TlvInfo v1 len=6 In: serial@21c0000 Out: serial@21c0000 Err: serial@21c0000 SEC0: RNG instantiated fsl_board_late_init PCA: failed to select bus 0 channel 11 PCA: failed to select bus 1 channel 11 Setting up retimer channels as 25Gbps Net: Warning: DPMAC3@xgmii (eth0) using random MAC address - ee:96:d2:25:a4:04 Warning: DPMAC4@xgmii (eth1) using random MAC address - 32:40:6c:43:b3:69 Warning: DPMAC5@25g-aui (eth2) using random MAC address - de:36:f0:f9:87:ad Warning: DPMAC6@25g-aui (eth3) using random MAC address - 0e:a8:f7:7a:00:c3 Warning: DPMAC11@rgmii (eth4) using random MAC address - c2:74:3d:ce:8f:dd Warning: DPMAC12@rgmii (eth5) using random MAC address - c2:7c:fd:c9:31:df Warning: DPMAC13@rgmii (eth6) using random MAC address - 6a:1b:31:c7:ad:6e Warning: DPMAC14@rgmii (eth7) using random MAC address - 7e:12:e4:7d:76:68 Warning: DPMAC15@rgmii (eth8) using random MAC address - 5e:64:27:a6:f3:fc Warning: DPMAC16@rgmii (eth9) using random MAC address - a6:cf:c4:12:c0:ad Warning: DPMAC17@rgmii (eth10) using random MAC address - 72:7c:7b:ef:be:b9 Warning: DPMAC18@rgmii (eth11) using random MAC address - b6:37:06:c3:5e:e2 eth0: DPMAC3@xgmii, eth1: DPMAC4@xgmii, eth2: DPMAC5@25g-aui, eth3: DPMAC6@25g-aui, eth4: DPMAC11@rgmii, eth5: DPMAC12@rgmii, eth6: DPMAC13@rgmii, eth7: DPMAC14@rgmii, eth8: DPMAC15@rgmii, eth9: DPMAC16@rgmii, ei switch to partitions #0, OK mmc1(part 0) is current device MMC read: dev # 1, block # 20480, count 4608 ... 4608 blocks read: OK MMC read: dev # 1, block # 28672, count 2048 ... 2048 blocks read: OK ``` Are the supported these card? I tried two 128 GB uSD Card from SanDisk and Samsung both doesn’t work SanDisk Extreme Pro 128GB uSD Card > **[data-sheet-extreme-pro-uhs-i-microsd-200mbps.pdf](https://documents.westerndigital.com/content/dam/doc-library/en_us/assets/public/sandisk/product/memory-cards/extreme-pro-uhs-i-microsd/data-sheet-extreme-pro-uhs-i-microsd-200mbps.pdf)** > > 981.76 KB Samsung Pro Plus 128GB uSD Card > **[2023\_samsung\_data\_sheet\_microsd\_card\_pro\_plus\_v1.1.pdf](https://download.semiconductor.samsung.com/resources/data-sheet/2023_samsung_data_sheet_microsd_card_pro_plus_v1.1.pdf)** > > 450.32 KB Both with this image ```auto lx2160acex7_2000_700_3200_8_5_2-2a7ab21.img.xz ``` ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 2, 2024, 5:29am UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/5 "2024-09-02T05:29:37Z")
Cloud you give some update how to fix this error? @jnettlet ---
**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\ **Post date:** [September 2, 2024, 5:44am UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/6 "2024-09-02T05:44:01Z")
> [@blien](#): > > Wrong Image Format for bootm command you can attach a .log file to include the full log. Thanks ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 4, 2024, 4:31pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/7 "2024-09-04T16:31:56Z")
Should I provide a log too? @jnettlet ---
**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\ **Post date:** [September 5, 2024, 7:44am UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/8 "2024-09-05T07:44:12Z")
sure thing. More data is always better…thanks ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 5, 2024, 9:14am UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/9 "2024-09-05T09:14:27Z")
[https://stackoverflow.com/questions/19469747/how-do-i-get-booting-log-for-u-boot](https://stackoverflow.com/questions/19469747/how-do-i-get-booting-log-for-u-boot) According this link there is no log from u-boot. You mean simply the whole output of the serial console saved a .log file? ---
**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\ **Post date:** [September 5, 2024, 9:22am UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/10 "2024-09-05T09:22:49Z")
yes. Most serial terminal applications support logging to a file. ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 5, 2024, 6:42pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/11 "2024-09-05T18:42:02Z")
@jnettlet Keys OFF | ON | ON | OFF | OFF First boot cycle with run sd\_bootcmd Second boot cycle with boot from mmc without interrupt autobooot [1.log](https://community.solid-run.com/uploads/short-url/sCac2FlfcmlhhxhXw12AOtOZomr.log) (57.8 KB) First boot cycle with keys ON | ON | ON | OFF | OFF Visually I see nothing in Serial Console but here is no second log because is empty ( 0 bytes) So I have no log for second boot process with direct boot from SD ---
**Author:** ![dstepanov](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/dstepanov/32/144_2.png) [@dstepanov](https://community.solid-run.com/u/dstepanov)\ **Post date:** [September 5, 2024, 6:44pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/12 "2024-09-05T18:44:56Z")
@Morta - you are trying to boot with prebuilt ramdisk provided by Solidrun (here is the link [lx2160a\_build/patches/ramdisk\_rootfs\_arm64.ext4.gz at master · SolidRun/lx2160a\_build · GitHub](https://github.com/SolidRun/lx2160a_build/blob/master/patches/ramdisk_rootfs_arm64.ext4.gz)) But this image is not valid, since it contains busybox as init and /etc/initab for SystemV init and they are not compatible (check here [The Buildroot user manual](https://buildroot.org/downloads/manual/manual.html#init-system)). And this is your error about this: ```auto Bad inittab entry at line 5 can’t open /dev/si: No such file or directory can’t open /dev/~~: No such file or directory can’t open /dev/l0: No such file or directory can’t open /dev/l1: No such file or directory can’t open /dev/l2: No such file or directory can’t open /dev/l3: No such file or directory can’t open /dev/l4: No such file or directory can’t open /dev/l5: No such file or directory can’t open /dev/l6: No such file or directory ``` Use this instruction [https://solidrun.atlassian.net/wiki/spaces/developer/pages/197494288/HoneyComb+LX2+ClearFog+CX+LX2+Quick+Start+Guide#Booting-from-an-SD-card](https://solidrun.atlassian.net/wiki/spaces/developer/pages/197494288/HoneyComb+LX2+ClearFog+CX+LX2+Quick+Start+Guide#Booting-from-an-SD-card) to boot from prebuilt SolidRun’s image ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 5, 2024, 6:49pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/13 "2024-09-05T18:49:17Z")
@dstepanov I also tried to build a image with Docker > **[lx2160acex7\_2000\_700\_3200\_LX2162A\_CLEARFOG\_18\_9\_0-3fbd680.img](https://drive.google.com/file/d/1XcpwBoE4xpQxYeR0GcOxdma41l877bov/view?usp=drive_link)** > > Google Drive file. lx2160acex7\_2000\_700\_3200\_LX2162A\_CLEARFOG\_18\_9\_0-3fbd680.img Same result with own builded image. I can provide also a log from this image, if necessary?! ---
**Author:** ![dstepanov](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/dstepanov/32/144_2.png) [@dstepanov](https://community.solid-run.com/u/dstepanov)\ **Post date:** [September 5, 2024, 6:59pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/14 "2024-09-05T18:59:39Z")
So which board are you using? lx2160acex7\_2000\_700\_3200\_LX2162A\_CLEARFOG\_18\_9\_0-3fbd680.img is for LX2162 ClearFog board which is completely different from LX2160A. And once again - you can’t boot into Ubuntu just after doing dd of that image to SD card. Some additional manipulations should be done Check this step-by-step instruction [https://solidrun.atlassian.net/wiki/spaces/developer/pages/197494288/HoneyComb+LX2+ClearFog+CX+LX2+Quick+Start+Guide#Booting-from-an-SD-card](https://solidrun.atlassian.net/wiki/spaces/developer/pages/197494288/HoneyComb+LX2+ClearFog+CX+LX2+Quick+Start+Guide#Booting-from-an-SD-card) ![image](https://europe1.discourse-cdn.com/flex005/uploads/solid_run/original/1X/68ce7198c7280dd9fd8c75146c4e62a0b8603482.png) ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 5, 2024, 7:02pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/15 "2024-09-05T19:02:14Z")
@dstepanov I have a LX2162a! Why isn’t possible to boot from uSD-Card directly? I don’t want flash the image to eMMC. This works without problem. I need more space than 8GB… ---
**Author:** ![dstepanov](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/dstepanov/32/144_2.png) [@dstepanov](https://community.solid-run.com/u/dstepanov)\ **Post date:** [September 5, 2024, 7:14pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/16 "2024-09-05T19:14:18Z")
You can boot from SD card, but not after doing dd of **that** image to SD card). Using provided instructions you can also program SD card: ```auto load mmc 0:1 0xa4000000 ubuntu-core.img # **mmc dev 1** - don't do this, don't switch to eMMC, copy ubuntu-core.img from SD to RAM and then write it to SD mmc write 0xa4000000 0 0xd2000 ``` Another way to program your SD card - extract correct image from you img file and use it: ```auto sudo mount -o offset=67108864 lx2160acex7_2000_700_3200_LX2162A_CLEARFOG_18_9_0-3fbd680.img /mnt/ ls -l /mnt/ total 424504 drwx------ 2 root root 16384 Jul 4 21:43 lost+found -rw-r--r-- 1 root root 434110464 Jul 4 21:43 ubuntu-core.img -rw-r--r-- 1 root root 131072 Jul 4 21:43 xspi_header.img sudo dd if=/mnt/ubuntu-core.img of=/dev/sda bs=1M conv=fdatasync ``` where /dev/sda is your SD card of course ---
**Author:** ![Morta](https://avatars.discourse-cdn.com/v4/letter/m/f05b48/32.png) [@Morta](https://community.solid-run.com/u/Morta)\ **Post date:** [September 5, 2024, 7:17pm UTC](https://community.solid-run.com/t/ubuntu-image-fails-to-boot-on-clearfog-lx2k/71/17 "2024-09-05T19:17:00Z")
@dstepanov you are my hero! Thanks for clarification \<3