# Hummingboard Mate devkit dip switches **URL:** \ **Category:** NXP i.MX8M Plus\ **Created:** [January 26, 2024, 11:43pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808 "2024-01-26T23:43:49Z")\ **Posts on this page:** 7\ **Page:** 1
**Author:** ![smatbd](https://avatars.discourse-cdn.com/v4/letter/s/a3d4f5/32.png) [@smatbd](https://community.solid-run.com/u/smatbd)\ **Post date:** [January 26, 2024, 11:43pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/1 "2024-01-26T23:43:49Z")
Hello, I am trying to get some things working on the hummingboard mate dev kit running Debian. I am following the guide, but I may have messed up the dip switches for boot selection by trying to interpret the grey/white squares of the other dip switches as positions to adjust. What do the other switches control and what position should they be in? Also has this quickstart page been tested? [https://solidrun.atlassian.net/wiki/spaces/developer/pages/263192632/HummingBoard+Mate+i.MX8M+Plus+SOM+Quick+Start+Guide](https://solidrun.atlassian.net/wiki/spaces/developer/pages/263192632/HummingBoard+Mate+i.MX8M+Plus+SOM+Quick+Start+Guide) I cannot get the board to boot using the referenced debian image, but going to one of the pulse images will boot, although hdmi and wifi doesn’t seem to be working. ---
**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\ **Post date:** [January 27, 2024, 8:15am UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/2 "2024-01-27T08:15:48Z")
Please reference this diagram. [https://solidrun.atlassian.net/wiki/spaces/developer/pages/287343073/HummingBoard+Pulse+Ripple+and+Pro+Boot+Select](https://solidrun.atlassian.net/wiki/spaces/developer/pages/287343073/HummingBoard+Pulse+Ripple+and+Pro+Boot+Select) ---
**Author:** ![smatbd](https://avatars.discourse-cdn.com/v4/letter/s/a3d4f5/32.png) [@smatbd](https://community.solid-run.com/u/smatbd)\ **Post date:** [January 27, 2024, 3:01pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/3 "2024-01-27T15:01:09Z")
Thanks, Using this configuration and debian image linked in the guide( sr-imx8-debian-bullseye-20230623-cli-imx8mp-sdhc.img.xz), if I try connect with kermit then I get ## Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options. … TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… done ---
**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\ **Post date:** [January 29, 2024, 3:03pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/4 "2024-01-29T15:03:33Z")
Please leave a serial console connected, preferably with logging enabled and collect the entire console log from power on. Thanks ---
**Author:** ![smatbd](https://avatars.discourse-cdn.com/v4/letter/s/a3d4f5/32.png) [@smatbd](https://community.solid-run.com/u/smatbd)\ **Post date:** [February 2, 2024, 3:21pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/5 "2024-02-02T15:21:35Z")
I was able to get back to this today. Here is the log ## Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options. U-Boot SPL 2020.04-00026-g0909dfb6 (Jun 14 2023 - 07:15:46 +0000) DDRINFO: start DRAM init DDRINFO: DRAM rate 3000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done DDR 4G Samsung identified! DDRINFO: start DRAM init DDRINFO: DRAM rate 4000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done Normal Boot Trying to boot from BOOTROM image offset 0x8000, pagesize 0x200, ivt offset 0x0 NOTICE: BL31: v2.2(release):rel\_imx\_5.4.70\_2.3.0-0-gf1d7187f NOTICE: BL31: Built : 07:15:43, Jun 14 2023 U-Boot 2020.04-00026-g0909dfb6 (Jun 14 2023 - 07:15:46 +0000) CPU: i.MX8MP[8] rev1.1 1800 MHz (running at 1200 MHz) CPU: Commercial temperature grade (0C to 95C) at 25C Reset cause: POR Model: NXP i.MX8MPlus LPDDR4 SolidRun board DRAM: 4 GiB MMC: FSL\_SDHC: 1, FSL\_SDHC: 2 Loading Environment from MMC… \*\*\* Warning - bad CRC, using default environment [\*]-Video Link 0probe video device failed, ret -2 ``` [0] lcd-controller@32e80000, video [1] mipi_dsi@32e60000, video_bridge [2] adv7535@39, panel ``` probe video device failed, ret -2 In: serial Out: serial Err: serial BuildInfo: - ATF f1d7187 - U-Boot 2020.04-00026-g0909dfb6 switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: board\_get\_mac: interface 0: using mac from tlv eeprom: D0:63:B4:05:83:8B Warning: ethernet@30bf0000 using MAC address from ROM eth1: ethernet@30bf0000 [PRIME] Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1… Found U-Boot script /boot/boot.scr 2544 bytes read in 17 ms (145.5 KiB/s) ## Executing script at 40480000 26333696 bytes read in 1108 ms (22.7 MiB/s) SCRIPT FAILED: continuing… Found U-Boot script /boot/boot.scr 2544 bytes read in 17 ms (145.5 KiB/s) ## Executing script at 40480000 26333696 bytes read in 1108 ms (22.7 MiB/s) SCRIPT FAILED: continuing… switch to partitions #0, OK mmc2(part 0) is current device \*\* No partition table - mmc 2 \*\* starting USB… Bus usb@38100000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus usb@38200000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@38100000 for devices… 1 USB Device(s) found scanning bus usb@38200000 for devices… 3 USB Device(s) found scanning usb for storage devices… 0 Storage Device(s) found Device 0: unknown device ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/01-d0-63-b4-05-83-8b ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-imx8m-imx8mp\_solidrun ethernet@30bf0000 Waiting for PHY auto negotiation to complete… TIMEOUT ! phy\_startup() failed: -110FAILED: -110missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-imx8m ---
**Author:** ![smatbd](https://avatars.discourse-cdn.com/v4/letter/s/a3d4f5/32.png) [@smatbd](https://community.solid-run.com/u/smatbd)\ **Post date:** [February 10, 2024, 6:07pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/6 "2024-02-10T18:07:56Z")
Any pointers? ---
**Author:** ![smatbd](https://avatars.discourse-cdn.com/v4/letter/s/a3d4f5/32.png) [@smatbd](https://community.solid-run.com/u/smatbd)\ **Post date:** [March 15, 2024, 9:17pm UTC](https://community.solid-run.com/t/hummingboard-mate-devkit-dip-switches/808/7 "2024-03-15T21:17:50Z")
Bump because this device is a paperweight right now and I would really like to use it.