# Hostapd and wifi 6e

**URL:** <https://community.solid-run.com/t/hostapd-and-wifi-6e/586>\
**Category:** OCTEON CN9130\
**Created:** [March 3, 2023, 10:26pm UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586 "2023-03-03T22:26:07Z")\
**Posts on this page:** 12\
**Page:** 1

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 3, 2023, 10:26pm UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/1 "2023-03-03T22:26:07Z")

</div>

Hy.  
I tried to use hostapd with a channel in 6ghz

The card wifi is a rz616 (mt 7922) with 6ghz :

> ```
> Bitrates (non-HT):
> * 6.0 Mbps
> * 9.0 Mbps
> * 12.0 Mbps
> * 18.0 Mbps
> * 24.0 Mbps
> * 36.0 Mbps
> * 48.0 Mbps
> * 54.0 Mbps
> Frequencies:
> * 5955 MHz [1] (23.0 dBm)
> * 5975 MHz [5] (23.0 dBm)
> * 5995 MHz [9] (23.0 dBm)
> * 6015 MHz [13] (23.0 dBm)
> * 6035 MHz [17] (23.0 dBm)
> * 6055 MHz [21] (23.0 dBm)
> * 6075 MHz [25] (23.0 dBm)
> * 6095 MHz [29] (23.0 dBm)
> * 6115 MHz [33] (23.0 dBm)
> * 6135 MHz [37] (23.0 dBm)
> * 6155 MHz [41] (23.0 dBm)
> * 6175 MHz [45] (23.0 dBm)
> * 6195 MHz [49] (23.0 dBm)
> * 6215 MHz [53] (23.0 dBm)
> * 6235 MHz [57] (23.0 dBm)
> * 6255 MHz [61] (23.0 dBm)
> * 6275 MHz [65] (23.0 dBm)
> * 6295 MHz [69] (23.0 dBm)
> * 6315 MHz [73] (23.0 dBm)
> * 6335 MHz [77] (23.0 dBm)
> * 6355 MHz [81] (23.0 dBm)
> * 6375 MHz [85] (23.0 dBm)
> * 6395 MHz [89] (23.0 dBm)
> * 6415 MHz [93] (23.0 dBm)
> * 6435 MHz [97] (disabled)
> 
> ```

In a first time, i tried to use a channel in 5ghz :

```auto
country_code=FR
interface=wlan1
ssid=doudoo_diagbox
wpa_passphrase=12345678
hw_mode=a
ieee80211d=1
ieee80211h=1
ieee80211n=1
ieee80211ac=1
ieee80211ax=1
wmm_enabled=1
preamble=1
ht_capab=[LDPC][HT40+][HT40-][GF][SHORT-GI-20][SHORT-GI-40]
vht_capab=[MAX-MPDU-7991][RXLDPC][SHORT-GI-80][MAX-A-MPDU-LEN-EXP3][RX-ANTENNA->
vht_oper_chwidth=1
he_oper_chwidth=1
channel=36
vht_oper_centr_freq_seg0_idx=42
he_oper_centr_freq_seg0_idx=42
he_su_beamformer=1
he_su_beamformee=1
he_mu_beamformer=1
auth_algs=1
wpa=2
wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256 SAE
rsn_pairwise=CCMP

```

And it works :

```auto
Station e0:d4:64:8e:1a:61 (on wlan1)
        inactive time: 612 ms
        rx bytes: 75427014
        rx packets: 88161
        tx bytes: 428212745
        tx packets: 304454
        tx retries: 0
        tx failed: 0
        rx drop misc: 0
        signal: -59 [-59, -87] dBm
        signal avg: -57 [-57, -87] dBm
        tx bitrate: 576.4 MBit/s 80MHz HE-MCS 5 HE-NSS 2 HE-GI 0 HE-DCM 0
        tx duration: 41439007 us
        rx bitrate: 144.1 MBit/s 80MHz HE-MCS 1 HE-NSS 2 HE-GI 0 HE-DCM 0
        rx duration: 4764512 us
        airtime weight: 256
        authorized: yes
        authenticated: yes
        associated: yes
        preamble: short
        WMM/WME: yes
        MFP: no
        TDLS peer: no
        DTIM period: 2
        beacon interval:100
        short preamble: yes
        short slot time:yes
        connected time: 576 seconds
        associated at [boottime]: 2320.641s
        associated at: 1677881469816 ms
        current time: 1677882046076 ms

```

Here,the Hostapd’s config for 6ghz channel :

> country\_code=FR  
> interface=wlan1  
> ssid=doudoo\_diagbox  
> wpa\_passphrase=12345678  
> hw\_mode=a  
> ieee80211d=1  
> ieee80211h=1  
> ieee80211n=1  
> ieee80211ac=1  
> ieee80211ax=1  
> wmm\_enabled=1  
> preamble=1  
> ht\_capab=[LDPC][HT40+][HT40-][GF][SHORT-GI-20][SHORT-GI-40]  
> #vht\_capab=[MAX-MPDU-7991][RXLDPC][SHORT-GI-80][MAX-A-MPDU-LEN-EXP3][RX-ANTENNA-\>  
> #he\_oper\_chwidth=1  
> channel=1  
> #vht\_oper\_centr\_freq\_seg0\_idx=42  
> he\_oper\_centr\_freq\_seg0\_idx=7  
> he\_su\_beamformer=1  
> he\_su\_beamformee=1  
> he\_mu\_beamformer=1  
> auth\_algs=1  
> wpa=2  
> wpa\_key\_mgmt=WPA-PSK WPA-PSK-SHA256 SAE  
> rsn\_pairwise=CCMP

Here the error output :

```auto
# hostapd wlan1.conf
rfkill: Cannot open RFKILL control device
wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Could not determine operating frequency
wlan1: interface state COUNTRY_UPDATE->DISABLED
wlan1: AP-DISABLED
wlan1: Unable to setup interface.
wlan1: interface state DISABLED->DISABLED
wlan1: AP-DISABLED
wlan1: CTRL-EVENT-TERMINATING
hostapd_free_hapd_data: Interface wlan1 wasn't started
nl80211: deinit ifname=wlan1 disabled_11b_rates=0

```

Can someone help me please :)?

Thank by advance

---

<div class="post-metadata">

**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\
**Post date:** [March 4, 2023, 5:12am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/2 "2023-03-04T05:12:10Z")

</div>

The 6GHz spectrum is a bit more regulated and I don’t believe you can just set the country\_code in the hostapd.conf. Can you try setting adding

```auto
options cfg80211 ieee80211_regdom=FR
in a /etc/modprobe.d/cfg80211.conf

```

to see if it helps?

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 4, 2023, 7:41am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/3 "2023-03-04T07:41:25Z")

</div>

Hy  
Thank you to answer me 🙂

I use a Buildroot Linux, based on busybox.  
I don’t have modprobe.d

But in a script on the boots, i launch the command Line : iw reg set FR .

IS it the same result?

---

<div class="post-metadata">

**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\
**Post date:** [March 4, 2023, 7:43am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/4 "2023-03-04T07:43:55Z")

</div>

no it needs to be set for the module. You should also be able to set it using a custom kernel commandline.

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 4, 2023, 8:05am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/5 "2023-03-04T08:05:06Z")

</div>

> [@jnettlet](#):
>
> `ieee80211_regdom=FR`

I load the module cfg80211 with option ieee80211\_regdom=FR.

```auto
# modprobe cfg80211 ieee80211_regdom=FR
[179.024573] cfg80211: Loading compiled-in X.509 certificates for regulatory d atabase
[179.032734] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
# modprobe mt7921e
[195.572910] mt7921e 0001:01:00.0: ASIC revision: 79220010
# [195.668022] mt7921e 0001:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20221227123154a
[195.668022]
[195.691868] mt7921e 0001:01:00.0: WM Firmware Version: ____ 000000, Build Time: 20221227123243

```

But same result for Hostapd.

```auto
# hostapd wlan0.conf
rfkill: Cannot open RFKILL control device
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Could not determine operating frequency
wlan0: interface state COUNTRY_UPDATE->DISABLED
wlan0: AP-DISABLED
wlan0: Unable to setup interface.
wlan0: interface state DISABLED->DISABLED
wlan0: AP-DISABLED
wlan0: CTRL-EVENT-TERMINATING
hostapd_free_hapd_data: Interface wlan0 wasn't started
nl80211: deinit ifname=wlan0 disabled_11b_rates=0

```

Here my config :

```auto
country_code=FR
interface=wlan1
ssid=doudoo_diagbox
wpa_passphrase=12345678
hw_mode=a
ieee80211d=1
ieee80211h=1
ieee80211n=1
ieee80211ac=1
ieee80211ax=1
wmm_enabled=1
preamble=1
#ht_capab=[LDPC][HT40+][HT40-][GF][SHORT-GI-20][SHORT-GI-40]
#vht_capab=[MAX-MPDU-7991][RXLDPC][SHORT-GI-80][MAX-A-MPDU-LEN-EXP3][RX-ANTENNA>
#vht_oper_chwidth=1
he_oper_chwidth=1
channel=1
#vht_oper_centr_freq_seg0_idx=42
he_oper_centr_freq_seg0_idx=7
he_su_beamformer=1
he_su_beamformee=1
he_mu_beamformer=1
auth_algs=1
wpa=2
wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256 SAE
rsn_pairwise=CCMP

```

---

<div class="post-metadata">

**Author:** ![jnettlet](https://dub1.discourse-cdn.com/flex005/user_avatar/community.solid-run.com/jnettlet/32/62_2.png) [@jnettlet](https://community.solid-run.com/u/jnettlet)\
**Post date:** [March 4, 2023, 8:14am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/6 "2023-03-04T08:14:22Z")

</div>

What kernel version are you using?

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 4, 2023, 8:18am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/7 "2023-03-04T08:18:02Z")

</div>

6.1

`https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tag/?h=v6.1`

I think it’s compatible with 6ghz.

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 4, 2023, 8:28am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/8 "2023-03-04T08:28:52Z")

</div>

I have tried with wpa supplicant too :

```auto
# nano wpa_supplicant.conf
  GNU nano 6.0 wpa_supplicant.conf
pmf=2
sae_pwe=1
network={
   mode=2
   ssid="doudoo"
   key_mgmt=SAE
   proto=RSN
   ieee80211w=2
   sae_password="12345678"
   pairwise=CCMP
   group=CCMP
   frequency=6015
}

# wpa_supplicant -i wlan0 -c wpa_supplicant.conf
Successfully initialized wpa_supplicant
rfkill: Cannot open RFKILL control device
[1873.309618] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
wlan0: CTRL-EVENT-CONNECTED - Connection to 38:e7:c0:ff:f8:7b completed [id=0 id_str=]

```

But i don’t see the wireless network ssid in my smartphone.

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 6, 2023, 1:10pm UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/9 "2023-03-06T13:10:23Z")

</div>

Hy 🙂 I think i found the problem.

> ```
> Band 4:
> HE Iftypes: managed
> HE MAC Capabilities (0x08011a000040):
> +HTC HE Supported
> Trigger Frame MAC Padding Duration: 2
> OM Control
> Maximum A-MPDU Length Exponent: 3
> A-MSDU in A-MPDU
> HE PHY Capabilities: (0x4c70ce120dc0b3064e3f00):
> HE40/HE80/5GHz
> HE160/5GHz
> 242 tone RUs/5GHz
> Device Class: 1
> LDPC Coding in Payload
> HE SU PPDU with 1x HE-LTF and 0.8us GI
> NDP with 4x HE-LTF and 3.2us GI
> STBC Tx <= 80MHz
> STBC Rx <= 80MHz
> Full Bandwidth UL MU-MIMO
> Partial Bandwidth UL MU-MIMO
> DCM Max Constellation: 2
> DCM Max Constellation Rx: 2
> SU Beamformee
> Beamformee STS <= 80Mhz: 3
> Ng = 16 SU Feedback
> Ng = 16 MU Feedback
> Codebook Size SU Feedback
> Codebook Size MU Feedback
> Triggered CQI Feedback
> Partial Bandwidth Extended Range
> PPE Threshold Present
> Power Boost Factor ar
> HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
> 20MHz in 40MHz HE PPDU 2.4GHz
> 20MHz in 160/80+80MHz HE PPDU
> 80MHz in 160/80+80MHz HE PPDU
> DCM Max BW: 1
> Longer Than 16HE SIG-B OFDM Symbols
> Non-Triggered CQI Feedback
> TX 1024-QAM
> RX 1024-QAM
> RX Full BW SU Using HE MU PPDU with Compression SIGB
> RX Full BW SU Using HE MU PPDU with Non-Compression SIGB
> HE RX MCS and NSS set <= 80 MHz
> 1 streams: MCS 0-11
> 2 streams: MCS 0-11
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> HE TX MCS and NSS set <= 80 MHz
> 1 streams: MCS 0-11
> 2 streams: MCS 0-11
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> HE RX MCS and NSS set 160 MHz
> 1 streams: MCS 0-11
> 2 streams: MCS 0-11
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> HE TX MCS and NSS set 160 MHz
> 1 streams: MCS 0-11
> 2 streams: MCS 0-11
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> PPE Threshold 0x39 0x1c 0xc7 0x71 0x1c 0x07
> HE Iftypes: AP
> HE MAC Capabilities (0x00011a081044):
> +HTC HE Supported
> BSR
> OM Control
> Maximum A-MPDU Length Exponent: 3
> BQR
> A-MSDU in A-MPDU
> OM Control UL MU Data Disable RX
> HE PHY Capabilities: (0x0420ce120000a000000c00):
> HE40/HE80/5GHz
> LDPC Coding in Payload
> NDP with 4x HE-LTF and 3.2us GI
> STBC Tx <= 80MHz
> STBC Rx <= 80MHz
> Full Bandwidth UL MU-MIMO
> Partial Bandwidth UL MU-MIMO
> DCM Max Constellation: 2
> DCM Max Constellation Rx: 2
> Partial Bandwidth Extended Range
> PPE Threshold Present
> TX 1024-QAM
> RX 1024-QAM
> HE RX MCS and NSS set <= 80 MHz
> 1 streams: MCS 0-11
> 2 streams: MCS 0-11
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> HE TX MCS and NSS set <= 80 MHz
> 1 streams: MCS 0-11
> 2 streams: MCS 0-11
> 3 streams: not supported
> 4 streams: not supported
> 5 streams: not supported
> 6 streams: not supported
> 7 streams: not supported
> 8 streams: not supported
> 
> ```

A part of the command line’s output : iw phy phy0 info

They are a part HE Iftypes: managed and for the AP mode : HE Iftypes: AP

And there is this int the part of AP :

> ```
> HE PHY Capabilities: (0x0420ce120000a000000c00):
> HE40/HE80/5GHz
> 
> ```

So i can’t use 6ghz and he 160mhz in ap mode ☹

---

<div class="post-metadata">

**Author:** ![mkoestler](https://avatars.discourse-cdn.com/v4/letter/m/43a26b/32.png) [@mkoestler](https://community.solid-run.com/u/mkoestler)\
**Post date:** [March 10, 2023, 8:50am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/10 "2023-03-10T08:50:16Z")

</div>

> [@doudootiana](#):
>
> So i can’t use 6ghz and he 160mhz in ap mode ☹

Hey there, today I came across your post while trying to set up a 6GHz AP on a NetGear A8000.

Actually the `HE PHY Capabilities` showing no 6GHz seems to not really be relevant here.  
I think you are just missing the `op_class` setting from your `hostapd` conf.

I am not done with testing but the following config snipped seems to successfully create a 6 GHz AP:

```auto
hw_mode=a
channel=57
ieee80211ax=1
wmm_enabled=1
op_class=131
ieee80211w=2
auth_algs=1
wpa=2
sae_password=password
wpa_key_mgmt=SAE
rsn_pairwise=CCMP

```

Note: You have to compile `hostapd` with `CONFIG_SAE=y` and you need `wpa_key_mgmt=SAE` because otherwise you will get the error `Management frame protection is required in 6 GHz` or `Invalid AKM suite for 6 GHz`.

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 10, 2023, 10:28am UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/11 "2023-03-10T10:28:04Z")

</div>

Hy,  
Thank you for your answer.

Thanks to your informations, i can launch Hostapd with 6ghz and 80mhz.

but i can’t connect my smartphone.

here the log of hostapd during connexion attempt :

> # hostapd wlan0.conf
> 
> rfkill: Cannot open RFKILL control device  
> wlan0: interface state UNINITIALIZED-\>COUNTRY\_UPDATE  
> [1572.868469] IPv6: ADDRCONF(NETDEV\_CHANGE): wlan0: link becomes ready  
> wlan0: interface state COUNTRY\_UPDATE-\>ENABLED  
> wlan0: AP-ENABLED  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: authentication OK (open system)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-AUTHENTICATE.indication(12:b2:01:f5:a5:ca, OPEN\_SYSTEM)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DELETEKEYS.request(12:b2:01:f5:a5:ca)  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: authenticated  
> wlan0: STA 12:b2:01:f5:a5:ca WPA: No PMKSA cache entry found for SAE  
> wlan0: STA 12:b2:01:f5:a5:ca WPA: event 3 notification  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.1X: unauthorizing port  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: deauthenticated  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DEAUTHENTICATE.indication(12:b2:01:f5:a5:ca, 1)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DELETEKEYS.request(12:b2:01:f5:a5:ca)  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: authentication OK (open system)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-AUTHENTICATE.indication(12:b2:01:f5:a5:ca, OPEN\_SYSTEM)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DELETEKEYS.request(12:b2:01:f5:a5:ca)  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: authenticated  
> wlan0: STA 12:b2:01:f5:a5:ca WPA: No PMKSA cache entry found for SAE  
> wlan0: STA 12:b2:01:f5:a5:ca WPA: event 3 notification  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.1X: unauthorizing port  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: deauthenticated  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DEAUTHENTICATE.indication(12:b2:01:f5:a5:ca, 1)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DELETEKEYS.request(12:b2:01:f5:a5:ca)  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: authentication OK (open system)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-AUTHENTICATE.indication(12:b2:01:f5:a5:ca, OPEN\_SYSTEM)  
> wlan0: STA 12:b2:01:f5:a5:ca MLME: MLME-DELETEKEYS.request(12:b2:01:f5:a5:ca)  
> wlan0: STA 12:b2:01:f5:a5:ca IEEE 802.11: authenticated  
> wlan0: STA 12:b2:01:f5:a5:ca WPA: No PMKSA cache entry found for SAE

---

<div class="post-metadata">

**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\
**Post date:** [March 10, 2023, 6:50pm UTC](https://community.solid-run.com/t/hostapd-and-wifi-6e/586/12 "2023-03-10T18:50:28Z")

</div>

Found the error 🙂

> # Algo de secu
> 
> ieee80211w=2  
> auth\_algs=3  
> wpa=2  
> wpa\_key\_mgmt=SAE  
> rsn\_pairwise=CCMP  
> rsn\_preauth=1  
> sae\_require\_mfp=1  
> sae\_pwe=1  
> wpa\_group\_rekey=1800  
> group\_cipher=CCMP  
> wpa\_psk\_radius=0