# Failed to boot **URL:** \ **Category:** OCTEON CN9130\ **Created:** [August 3, 2022, 10:11pm UTC](https://community.solid-run.com/t/failed-to-boot/418 "2022-08-03T22:11:38Z")\ **Posts on this page:** 5\ **Page:** 1
**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\ **Post date:** [August 3, 2022, 10:11pm UTC](https://community.solid-run.com/t/failed-to-boot/418/1 "2022-08-03T22:11:38Z")
Hy, I have a clearfog pro cn9130. Impossible to boot, it blocks at ‘starting kernel …’ Here the log of the boot : ```auto BootROM - 2.03 Starting CP-0 IOROM 1.07 Booting from SD 0 (0x29) Found valid image at boot postion 0x002 lNOTICE: Starting binary extension NOTICE: SVC: DEV ID: CN913x, FREQ Mode: 0x0 NOTICE: SVC: AVS work point changed from 0x2e7 to 0x2de w/o ecc; strap value=0 4GB capacity; strap value=0 mv_ddr: 14.0.0-g305d923-dirty (Aug 03 2022 - 17:55:23) SSCG_EN Synopsys DDR43 PHY Firmware version: A-2017.11 SNPS DDR: 1D training passed SNPS DDR: 2D training passed SNPS DDR: training completed dma memcmp pass mv_ddr: completed successfully NOTICE: Cold boot NOTICE: Booting Trusted Firmware NOTICE: BL1: v2.3(release):v2.3-862-g00ad74c7a-dirty (Marvell-devel-18.12.0) NOTICE: BL1: Built : 17:55:24, Aug 3 2022 NOTICE: BL1: Booting BL2 NOTICE: BL2: v2.3(release):v2.3-862-g00ad74c7a-dirty (Marvell-devel-18.12.0) NOTICE: BL2: Built : 17:55:24, Aug 3 2022 NOTICE: SCP_BL2 contains 7 concatenated images NOTICE: Skipping MG CP1 related image NOTICE: Load image to CP0 MG NOTICE: Loading MG image from address 0x403114c Size 0xe0f0 to MG at 0xf2100000 NOTICE: Skipping MSS CP3 related image NOTICE: Skipping MSS CP2 related image NOTICE: Skipping MSS CP1 related image NOTICE: Load image to CP0 MSS AP0 NOTICE: Loading MSS image from addr. 0x4044930 Size 0x1cfc to MSS at 0xf2280000 NOTICE: Done NOTICE: Load image to AP0 MSS NOTICE: Loading MSS image from addr. 0x404662c Size 0x5400 to MSS at 0xf0580000 NOTICE: Done NOTICE: BL1: Booting BL31 lNOTICE: BL31: v2.3(release):v2.3-862-g00ad74c7a-dirty (Marvell-devel-18.12.0) NOTICE: BL31: Built : 17:55:24, Aug 3 2022 U-Boot 2019.10-10.0.0-dirty (Aug 03 2022 - 17:45:53 +0200) Model: SolidRun CN9130 based SOM ClearFog Pro **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **SoC: cn9130-A1; AP807-B0; CP115-A0** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **Clock: CPU 2000 [MHz]** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **DDR 1200 [MHz]** **ERROR: mrvl_sip_smc_handler: unhandled SMC (0x82000014)** **FABRIC 1200 [MHz]** **MSS 200 [MHz]** LLC Enabled (Exclusive Mode) DRAM: 4 GiB Running in RAM - U-Boot at: 0x7fef0000 Env at: 0x7ff9c1ef Comphy chip #0: Comphy-0: SATA1 Comphy-1: USB3_HOST0 Comphy-2: SFI0 10.3125 Gbps Comphy-3: SGMII1 1.25 Gbps Comphy-4: PEX1 Comphy-5: PEX2 UTMI PHY 0 initialized to USB Host0 UTMI PHY 1 initialized to USB Host1 PCIE-0: Link down PCIE-2: Link down NAND: 0 MiB MMC: sdhci@6e0000: 0, sdhci@780000: 1 **Loading Environment from MMC...*** Warning - bad CRC, using default environment** **get_tlvinfo_from_eeprom: failed to read from eeprom!** **get_fdtfile_from_tlv_eeprom: could not identify carrier, defaulting to Clearfog Pro!** **Net:** Warning: mvpp2-0 (eth0) using random MAC address - ca:87:b0:95:12:c6 eth0: mvpp2-0 [PRIME] Warning: mvpp2-1 (eth1) using random MAC address - b2:be:e3:b2:48:e5 , eth1: mvpp2-1 Warning: mvpp2-2 (eth2) using random MAC address - 72:23:99:d6:7c:ba , eth2: mvpp2-2 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 230 bytes read in 15 ms (14.6 KiB/s) 1: primary kernel Retrieving file: /extlinux/Image-alpha 36076032 bytes read in 3211 ms (10.7 MiB/s) append: console=ttyS0,115200 root=PARTUUID=30303030-01 rw rootwait Retrieving file: /extlinux/cn9130-cf-pro-alpha.dtb 24921 bytes read in 25 ms (972.7 KiB/s) ## Flattened Device Tree blob at 06f00000 Booting using the fdt blob at 0x6f00000 Loading Device Tree to 000000007f5ce000, end 000000007f5d7158 ... OK **Starting kernel ...** ``` The kernel version is 5.19. I have applied all patches found in the github. In the first time, i have build an ubuntu img thanks to the script runme. In the folders, i have found the .config for linux, i have used this one. To generate the flash-image.bin, i followed in script runme, the steps about u-boot and atf. Is it a problem with u-boot or kernel, i don’t find ☹ Thank by advance. If you need, i can share the configuration for my kernel,uboot or another ---
**Author:** ![ROBPER](https://avatars.discourse-cdn.com/v4/letter/r/85f322/32.png) [@ROBPER](https://community.solid-run.com/u/ROBPER)\ **Post date:** [August 4, 2022, 6:08am UTC](https://community.solid-run.com/t/failed-to-boot/418/2 "2022-08-04T06:08:08Z")
Hi, I had a similar issue with SolidRun CN9130 base, first time I tried to install on microSD card. Following the support page informationand “mixing” them with the information under Git, I got the system booting from microSD (using the SPI boot) and then with eMMC too. I used the “ready to use image file”. I can share the message from tty console, if this can help Thank You ---
**Author:** ![ROBPER](https://avatars.discourse-cdn.com/v4/letter/r/85f322/32.png) [@ROBPER](https://community.solid-run.com/u/ROBPER)\ **Post date:** [August 4, 2022, 6:41am UTC](https://community.solid-run.com/t/failed-to-boot/418/3 "2022-08-04T06:41:41Z")
Here You go my console messages, CN9130 base: * * * BootROM - 2.03 Starting AP IOROM 1.02 Booting from eMMC 0 Found valid image at boot postion 0x000 lNOTICE: Starting binary extension NOTICE: SVC: DEV ID: CN913x, FREQ Mode: 0x0 NOTICE: SVC: AVS work point changed from 0x2de to 0x2d8 w/o ecc; strap value=0 4GB capacity; strap value=0 mv\_ddr: 14.0.0-g666afa1 (Jul 07 2022 - 19:32:54) SSCG\_EN Synopsys DDR43 PHY Firmware version: A-2017.11 SNPS DDR: 1D training passed SNPS DDR: 2D training passed SNPS DDR: training completed dma memcmp pass mv\_ddr: completed successfully NOTICE: Cold boot NOTICE: Booting Trusted Firmware NOTICE: BL1: v2.3(release):v2.3-864-gcb1856237 (Marvell-devel-18.12.0) NOTICE: BL1: Built : 19:32:54, Jul 7 2022 NOTICE: BL1: Booting BL2 NOTICE: BL2: v2.3(release):v2.3-864-gcb1856237 (Marvell-devel-18.12.0) NOTICE: BL2: Built : 19:32:54, Jul 7 2022 NOTICE: SCP\_BL2 contains 7 concatenated images NOTICE: Skipping MG CP1 related image NOTICE: Load image to CP0 MG NOTICE: Loading MG image from address 0x403114c Size 0xe0f0 to MG at 0xf2100000 NOTICE: Skipping MSS CP3 related image NOTICE: Skipping MSS CP2 related image NOTICE: Skipping MSS CP1 related image NOTICE: Load image to CP0 MSS AP0 NOTICE: Loading MSS image from addr. 0x4044930 Size 0x1cfc to MSS at 0xf2280000 NOTICE: Done NOTICE: Load image to AP0 MSS NOTICE: Loading MSS image from addr. 0x404662c Size 0x5400 to MSS at 0xf0580000 NOTICE: Done NOTICE: BL1: Booting BL31 lNOTICE: BL31: v2.3(release):v2.3-864-gcb1856237 (Marvell-devel-18.12.0) NOTICE: BL31: Built : 19:32:54, Jul 7 2022 U-Boot 2019.10-10.0.0-00018-g15bfc87307 (Jul 07 2022 - 19:32:53 +0000) Model: SolidRun CN9130 based SOM ClearFog Base ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) SoC: cn9130-A1; AP807-B0; CP115-A0 ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) Clock: CPU 2000 [MHz] ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) DDR 1200 [MHz] ERROR: mrvl\_sip\_smc\_handler: unhandled SMC (0x82000014) FABRIC 1200 [MHz] MSS 200 [MHz] LLC Enabled (Exclusive Mode) DRAM: 4 GiB Running in RAM - U-Boot at: 0x7fef0000 Env at: 0x7ff9c1ef Comphy chip #0: Comphy-0: SATA1 Comphy-1: USB3\_HOST0 Comphy-2: SFI0 10.3125 Gbps Comphy-3: SGMII1 1.25 Gbps Comphy-4: USB3\_HOST1 Comphy-5: PEX2 UTMI PHY 0 initialized to USB Host0 UTMI PHY 1 initialized to USB Host1 PCIE-0: Link down NAND: 0 MiB MMC: sdhci@6e0000: 0, sdhci@780000: 1 Loading Environment from MMC… \*\*\* Warning - bad CRC, using default environment get\_fdtfile\_from\_tlv\_eeprom: could not identify carrier, defaulting to Clearfog Pro! Net: Warning: mvpp2-0 (eth0) using random MAC address - 06:e0:ce:a8:e2:3c eth0: mvpp2-0 [PRIME] Warning: mvpp2-1 (eth1) using random MAC address - 5a:85:03:22:75:7a , eth1: mvpp2-1 Warning: mvpp2-2 (eth2) using random MAC address - 5e:2c:2f:d4:df:a3 , eth2: mvpp2-2 Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1… Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 239 bytes read in 11 ms (20.5 KiB/s) 1: primary kernel Retrieving file: /boot/Image 30153216 bytes read in 2023 ms (14.2 MiB/s) append: console=ttyS0,115200 root=PARTUUID=30303030-01 rw rootwait Retrieving file: /boot/cn9130-cf-base.dtb 22934 bytes read in 17 ms (1.3 MiB/s) ## Flattened Device Tree blob at 06f00000 Booting using the fdt blob at 0x6f00000 Loading Device Tree to 000000007f5ce000, end 000000007f5d6995 … OK Starting kernel … [0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [0.000000] Linux version 5.8.0-00006-g6da046907c97-dirty (alon@tr2) (aarch64-linux-gnu-gcc (Linaro GCC 7.5-2019.12) 7.5.0, GNU ld (Linaro\_Binutils-2019.12) 2.28.2.20170706) #4 SMP PREEMPT Thu Jun 24 16:44:14 IDT 2021 [0.000000] Machine model: SolidRun CN9130 based SOM Clearfog Base [0.000000] efi: UEFI not found. [0.000000] cma: Reserved 32 MiB at 0x00000000be000000 [0.000000] NUMA: No NUMA configuration found [0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000013fffffff] [0.000000] NUMA: NODE\_DATA [mem 0x13f7e0100-0x13f7e1fff] [0.000000] Zone ranges: [0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff] [0.000000] DMA32 [mem 0x0000000040000000-0x00000000ffffffff] [0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [0.000000] Movable zone start for each node [0.000000] Early memory node ranges [0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [0.000000] node 0: [mem 0x0000000004200000-0x00000000bfffffff] [0.000000] node 0: [mem 0x0000000100000000-0x000000013fffffff] [0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000013fffffff] [0.000000] psci: probing for conduit method from DT. [0.000000] psci: PSCIv1.1 detected in firmware. [0.000000] psci: Using standard PSCI v0.2 function IDs [0.000000] psci: MIGRATE\_INFO\_TYPE not supported. [0.000000] psci: SMC Calling Convention v1.2 [0.000000] percpu: Embedded 23 pages/cpu s53912 r8192 d32104 u94208 [0.000000] Detected PIPT I-cache on CPU0 [0.000000] CPU features: detected: EL2 vector hardening [0.000000] Speculative Store Bypass Disable mitigation not required [0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031680 [0.000000] Policy zone: Normal [0.000000] Kernel command line: console=ttyS0,115200 root=PARTUUID=30303030-01 rw rootwait [0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [0.000000] software IO TLB: mapped [mem 0x3bfff000-0x3ffff000] (64MB) [0.000000] Memory: 3983216K/4192256K available (14012K kernel code, 2182K rwdata, 7572K rodata, 5632K init, 483K bss, 176272K reserved, 32768K cma-reserved) [0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [0.000000] rcu: Preemptible hierarchical RCU implementation. [0.000000] rcu: RCU event tracing is enabled. [0.000000] rcu: RCU restricting CPUs from NR\_CPUS=256 to nr\_cpu\_ids=4. [0.000000] Trampoline variant of Tasks RCU enabled. [0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [0.000000] rcu: Adjusting geometry for rcu\_fanout\_leaf=16, nr\_cpu\_ids=4 [0.000000] NR\_IRQS: 64, nr\_irqs: 64, preallocated irqs: 0 [0.000000] GIC: Adjusting CPU interface base to 0x00000000f022f000 [0.000000] GIC: Using split EOI/Deactivate mode [0.000000] GICv2m: DT overriding V2M MSI\_TYPER (base:160, num:32) [0.000000] GICv2m: range[mem 0xf0280000-0xf0280fff], SPI[160:191] [0.000000] GICv2m: DT overriding V2M MSI\_TYPER (base:192, num:32) [0.000000] GICv2m: range[mem 0xf0290000-0xf0290fff], SPI[192:223] [0.000000] GICv2m: DT overriding V2M MSI\_TYPER (base:224, num:32) [0.000000] GICv2m: range[mem 0xf02a0000-0xf02a0fff], SPI[224:255] [0.000000] GICv2m: DT overriding V2M MSI\_TYPER (base:256, num:32) [0.000000] GICv2m: range[mem 0xf02b0000-0xf02b0fff], SPI[256:287] [0.000000] random: get\_random\_bytes called from start\_kernel+0x314/0x4f0 with crng\_init=0 [0.000000] arch\_timer: cp15 timer(s) running at 25.00MHz (phys). [0.000000] clocksource: arch\_sys\_counter: mask: 0xffffffffffffff max\_cycles: 0x5c40939b5, max\_idle\_ns: 440795202646 ns [0.000001] sched\_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [0.000206] Console: colour dummy device 80x25 [0.000244] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [0.000248] pid\_max: default: 32768 minimum: 301 [0.000279] LSM: Security Framework initializing [0.000314] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [0.000329] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [0.000921] rcu: Hierarchical SRCU implementation. [0.001470] EFI services will not be available. [0.001560] smp: Bringing up secondary CPUs … [0.001965] Detected PIPT I-cache on CPU1 [0.001998] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [0.002419] Detected PIPT I-cache on CPU2 [0.002441] CPU2: Booted secondary processor 0x0000000100 [0x410fd083] [0.002857] Detected PIPT I-cache on CPU3 [0.002873] CPU3: Booted secondary processor 0x0000000101 [0x410fd083] [0.002905] smp: Brought up 1 node, 4 CPUs [0.002913] SMP: Total of 4 processors activated. [0.002916] CPU features: detected: 32-bit EL0 Support [0.002919] CPU features: detected: CRC32 instructions [0.002922] CPU features: detected: 32-bit EL1 Support [0.011462] CPU: All CPU(s) started at EL2 [0.011478] alternatives: patching kernel code [0.012213] devtmpfs: initialized [0.013695] KASLR disabled due to lack of seed [0.013891] clocksource: jiffies: mask: 0xffffffff max\_cycles: 0xffffffff, max\_idle\_ns: 7645041785100000 ns [0.013899] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [0.014215] pinctrl core: initialized pinctrl subsystem [0.014591] thermal\_sys: Registered thermal governor ‘step\_wise’ [0.014592] thermal\_sys: Registered thermal governor ‘power\_allocator’ [0.014851] DMI not present or invalid. [0.015086] NET: Registered protocol family 16 [0.015307] DMA: preallocated 512 KiB GFP\_KERNEL pool for atomic allocations [0.015383] DMA: preallocated 512 KiB GFP\_KERNEL|GFP\_DMA pool for atomic allocations [0.015460] DMA: preallocated 512 KiB GFP\_KERNEL|GFP\_DMA32 pool for atomic allocations [0.015478] audit: initializing netlink subsys (disabled) [0.015541] audit: type=2000 audit(0.012:1): state=initialized audit\_enabled=0 res=1 [0.015925] cpuidle: using governor menu [0.016009] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [0.016048] ASID allocator initialised with 65536 entries [0.016460] Serial: AMBA PL011 UART driver [0.028167] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [0.028172] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [0.028175] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [0.028177] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [0.028694] cryptd: max\_cpu\_qlen set to 1000 [0.029739] ACPI: Interpreter disabled. [0.030535] ap0\_sd\_vccq: Bringing 3300000uV into 1800000-1800000uV [0.030814] iommu: Default domain type: Translated [0.030934] vgaarb: loaded [0.031066] SCSI subsystem initialized [0.031221] usbcore: registered new interface driver usbfs [0.031238] usbcore: registered new interface driver hub [0.031263] usbcore: registered new device driver usb [0.031685] pps\_core: LinuxPPS API ver. 1 registered [0.031688] pps\_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [giometti@linux.it](mailto:giometti@linux.it) [0.031694] PTP clock support registered [0.031747] EDAC MC: Ver: 3.0.0 [0.032289] FPGA manager framework [0.032321] Advanced Linux Sound Architecture Driver Initialized. [0.032606] clocksource: Switched to clocksource arch\_sys\_counter [0.032686] VFS: Disk quotas dquot\_6.6.0 [0.032709] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [0.032779] pnp: PnP ACPI: disabled [0.034892] NET: Registered protocol family 2 [0.035058] tcp\_listen\_portaddr\_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [0.035083] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [0.035188] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [0.035393] TCP: Hash tables configured (established 32768 bind 32768) [0.035450] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [0.035492] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [0.035581] NET: Registered protocol family 1 [0.035762] RPC: Registered named UNIX socket transport module. [0.035765] RPC: Registered udp transport module. [0.035767] RPC: Registered tcp transport module. [0.035769] RPC: Registered tcp NFSv4.1 backchannel transport module. [0.035775] PCI: CLS 0 bytes, default 64 [0.036045] hw perfevents: unable to count PMU IRQs [0.036054] hw perfevents: /ap807/config-space@f0000000/pmu: failed to register PMU devices! [0.036171] kvm [1]: IPA Size Limit: 44bits [0.036506] kvm [1]: vgic interrupt IRQ1 [0.036569] kvm [1]: Hyp mode initialized successfully [0.038171] Initialise system trusted keyrings [0.038233] workingset: timestamp\_bits=44 max\_order=20 bucket\_order=0 [0.040268] squashfs: version 4.0 (2009/01/31) Phillip Lougher [0.040527] NFS: Registering the id\_resolver key type [0.040536] Key type id\_resolver registered [0.040539] Key type id\_legacy registered [0.040545] nfs4filelayout\_init: NFSv4 File Layout Driver Registering… [0.040621] 9p: Installing v9fs 9p2000 file system support [0.059897] Key type asymmetric registered [0.059900] Asymmetric key parser ‘x509’ registered [0.059917] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [0.059920] io scheduler mq-deadline registered [0.059923] io scheduler kyber registered [0.063458] armada-ap806-pinctrl f06f4000.system-controller:pinctrl: registered pinctrl driver [0.063777] armada-cp110-pinctrl f2440000.system-controller:pinctrl: registered pinctrl driver [0.064795] gpio-59 (phy\_reset): hogged as output/high [0.066474] EINJ: ACPI disabled. [0.069633] mv\_xor\_v2 f0400000.xor: Marvell Version 2 XOR driver [0.069882] mv\_xor\_v2 f0420000.xor: Marvell Version 2 XOR driver [0.070144] mv\_xor\_v2 f0440000.xor: Marvell Version 2 XOR driver [0.070403] mv\_xor\_v2 f0460000.xor: Marvell Version 2 XOR driver [0.070732] mv\_xor\_v2 f26a0000.xor: Marvell Version 2 XOR driver [0.071005] mv\_xor\_v2 f26c0000.xor: Marvell Version 2 XOR driver [0.074452] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [0.075165] printk: console [ttyS0] disabled [0.095497] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 8, base\_baud = 12500000) is a 16550A [1.063462] printk: console [ttyS0] enabled [1.068194] SuperH (H)SCI(F) driver initialized [1.073013] msm\_serial: driver initialized [1.080664] loop: module loaded [1.084243] megasas: 07.714.04.00-rc1 [1.088270] ahci f2540000.sata: supply ahci not found, using dummy regulator [1.095386] ahci f2540000.sata: supply phy not found, using dummy regulator [1.102805] platform f2540000.sata:sata-port@0: supply target not found, using dummy regulator [1.111777] platform f2540000.sata:sata-port@1: supply target not found, using dummy regulator [1.120509] ahci f2540000.sata: masking port\_map 0x3 → 0x3 [1.126141] ahci f2540000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [1.134706] ahci f2540000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [1.143306] scsi host0: ahci [1.146409] scsi host1: ahci [1.149370] ata1: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x100 irq 25 [1.157325] ata2: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x180 irq 25 [1.166877] spi-nor spi2.0: s25fl064k (8192 Kbytes) [1.172529] spi-nor spi2.1: unrecognized JEDEC id bytes: ff ff ff ff ff ff [1.179451] spi-nor: probe of spi2.1 failed with error -2 [1.185893] libphy: Fixed MDIO Bus: probed [1.190329] tun: Universal TUN/TAP device driver, 1.6 [1.195790] thunder\_xcv, ver 1.0 [1.199051] thunder\_bgx, ver 1.0 [1.202319] nicpf, ver 1.0 [1.205561] hclge is initializing [1.208914] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [1.216170] hns3: Copyright (c) 2017 Huawei Corporation. [1.221530] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [1.228609] e1000: Copyright (c) 1999-2006 Intel Corporation. [1.234406] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [1.240264] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [1.246221] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k [1.253212] igb: Copyright (c) 2007-2014 Intel Corporation. [1.258821] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [1.266687] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [1.272843] libphy: orion\_mdio\_bus: probed [1.278145] mvpp2 f2000000.ethernet: using 8 per-cpu buffers [1.289531] sky2: driver version 1.30 [1.293714] VFIO - User Level meta-driver version: 0.3 [1.299679] ehci\_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver [1.306246] ehci-pci: EHCI PCI platform driver [1.310721] ehci-platform: EHCI generic platform driver [1.316038] ehci-orion: EHCI orion driver [1.320121] ehci-exynos: EHCI Exynos driver [1.324369] ohci\_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver [1.330586] ohci-pci: OHCI PCI platform driver [1.335063] ohci-platform: OHCI generic platform driver [1.340372] ohci-exynos: OHCI Exynos driver [1.344813] xhci-hcd f2500000.usb3: xHCI Host Controller [1.350163] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 1 [1.357739] xhci-hcd f2500000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [1.367021] xhci-hcd f2500000.usb3: irq 26, io mem 0xf2500000 [1.373094] hub 1-0:1.0: USB hub found [1.376874] hub 1-0:1.0: 1 port detected [1.380919] xhci-hcd f2500000.usb3: xHCI Host Controller [1.386260] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 2 [1.393779] xhci-hcd f2500000.usb3: Host supports USB 3.0 SuperSpeed [1.400179] usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM. [1.408473] hub 2-0:1.0: USB hub found [1.412250] hub 2-0:1.0: 1 port detected [1.416367] xhci-hcd f2510000.usb3: xHCI Host Controller [1.421721] xhci-hcd f2510000.usb3: new USB bus registered, assigned bus number 3 [1.429290] xhci-hcd f2510000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [1.438567] xhci-hcd f2510000.usb3: irq 27, io mem 0xf2510000 [1.444582] hub 3-0:1.0: USB hub found [1.448359] hub 3-0:1.0: 1 port detected [1.452388] xhci-hcd f2510000.usb3: xHCI Host Controller [1.457732] xhci-hcd f2510000.usb3: new USB bus registered, assigned bus number 4 [1.465251] xhci-hcd f2510000.usb3: Host supports USB 3.0 SuperSpeed [1.471651] usb usb4: We don’t know the algorithms for LPM for this host, disabling LPM. [1.478784] ata1: SATA link down (SStatus 0 SControl 300) [1.479935] hub 4-0:1.0: USB hub found [1.485223] ata2: SATA link down (SStatus 0 SControl 300) [1.488977] hub 4-0:1.0: 1 port detected [1.498635] usbcore: registered new interface driver usb-storage [1.504721] usbcore: registered new interface driver ftdi\_sio [1.510501] usbserial: USB Serial support registered for FTDI USB Serial Device [1.517892] usbcore: registered new interface driver option [1.523495] usbserial: USB Serial support registered for GSM modem (1-port) [1.531686] armada38x-rtc f2284000.rtc: registered as rtc0 [1.537215] armada38x-rtc f2284000.rtc: setting system clock to 2022-08-04T06:28:11 UTC (1659594491) [1.546852] i2c /dev entries driver [1.550943] pca953x 0-0020: supply vcc not found, using dummy regulator [1.557625] pca953x 0-0020: using no AI [1.562623] gpio-496 (pcie1.0-clkreq): hogged as input [1.568823] gpio-499 (pcie1.0-w-disable): hogged as output/low [1.574987] gpio-501 (usb3-current-limit): hogged as input [1.581112] gpio-502 (usb3-power): hogged as output/high [1.587899] gpio-507 (m.2 devslp): hogged as output/low [1.593349] at24 0-0053: supply vcc not found, using dummy regulator [1.600217] at24 0-0053: 256 byte 24c02 EEPROM, writable, 16 bytes/write [1.608265] mcp3021 0-004c: hwmon\_device\_register() is deprecated. Please convert the driver to use hwmon\_device\_register\_with\_info(). [1.634832] sbsa-gwdt f0610000.watchdog: Initialized with 10s timeout @ 25000000 Hz, action=0. [1.644245] sdhci: Secure Digital Host Controller Interface driver [1.650468] sdhci: Copyright(c) Pierre Ossman [1.655064] Synopsys Designware Multimedia Card Interface Driver [1.661604] sdhci-pltfm: SDHCI platform and OF driver helper [1.698772] mmc0: SDHCI controller on f06e0000.sdhci [f06e0000.sdhci] using ADMA 64-bit [1.707035] xenon-sdhci f2780000.sdhci: Got CD GPIO [1.742920] mmc1: SDHCI controller on f2780000.sdhci [f2780000.sdhci] using ADMA 64-bit [1.751287] ledtrig-cpu: registered to indicate activity on CPUs [1.758055] usbcore: registered new interface driver usbhid [1.763672] usbhid: USB HID core driver [1.769847] NET: Registered protocol family 17 [1.774388] 9pnet: Installing 9P2000 support [1.778700] Key type dns\_resolver registered [1.783157] registered taskstats version 1 [1.787291] Loading compiled-in X.509 certificates [1.793595] hw perfevents: enabled with armv8\_cortex\_a72 PMU driver, 7 counters available [1.802500] armada8k-pcie f2640000.pcie: host bridge /cp0/pcie@f2640000 ranges: [1.809885] armada8k-pcie f2640000.pcie: MEM 0x00e1000000..0x00e1efffff → 0x00e1000000 [1.818386] mmc0: new high speed MMC card at address 0001 [1.824084] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB [1.828760] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB [1.834859] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB [1.840887] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (234:0) [1.848900] mmcblk0: p1 [2.834783] armada8k-pcie f2640000.pcie: Phy link never came up [2.840737] armada8k-pcie f2640000.pcie: Link not up after reconfiguration [2.847708] armada8k-pcie f2640000.pcie: PCI host bridge to bus 0000:00 [2.854356] pci\_bus 0000:00: root bus resource [bus 00-ff] [2.859867] pci\_bus 0000:00: root bus resource [mem 0xe1000000-0xe1efffff] [2.866785] pci 0000:00:00.0: [11ab:0110] type 01 class 0x060400 [2.872833] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [2.879171] pci 0000:00:00.0: supports D1 D2 [2.883461] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [2.890308] pci 0000:00:00.0: BAR 0: assigned [mem 0xe1000000-0xe10fffff] [2.897133] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [3.260958] pcieport 0000:00:00.0: PME: Signaling with IRQ 36 [3.267322] libphy: SFP I2C Bus: probed [3.272147] sfp sfp-eth@0: Host maximum power 2.0W [3.279489] mvpp2 f2000000.ethernet: using 8 per-cpu buffers [3.302953] mvpp2 f2000000.ethernet eth0: Using random mac address 8a:ba:1b:37:08:42 [3.313396] mvpp2 f2000000.ethernet eth1: Using random mac address ba:e6:63:18:68:7c [3.322665] mvpp2 f2000000.ethernet eth2: Using random mac address 76:7b:8e:7b:bd:87 [3.340881] ALSA device list: [3.343863] No soundcards found. [3.445632] random: fast init done [3.461990] EXT4-fs (mmcblk0p1): recovery complete [3.467331] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [3.475473] ext4 filesystem being mounted at /root supports timestamps until 2038 (0x7fffffff) [3.484141] VFS: Mounted root (ext4 filesystem) on device 179:1. [3.490545] devtmpfs: mounted [3.494787] Freeing unused kernel memory: 5632K [3.499396] Run /sbin/init as init process [3.824093] NET: Registered protocol family 10 [3.828998] Segment Routing with IPv6 [3.849453] systemd[1]: systemd 245.4-4ubuntu3.17 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid) [3.872303] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 20.04.4 LTS! ---
**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\ **Post date:** [August 4, 2022, 8:33am UTC](https://community.solid-run.com/t/failed-to-boot/418/4 "2022-08-04T08:33:37Z")
Hy, thank you for your Answer. I will do with your informations after my work ^^ thanks again ---
**Author:** ![doudootiana](https://avatars.discourse-cdn.com/v4/letter/d/5f8ce5/32.png) [@doudootiana](https://community.solid-run.com/u/doudootiana)\ **Post date:** [August 6, 2022, 6:05pm UTC](https://community.solid-run.com/t/failed-to-boot/418/5 "2022-08-06T18:05:16Z")
Hy Robper, I have solved my problem ^^ In my first post, i have forgo to say I use buildroot to make my custom OS. I have used the runme.sh just to see the .config for the Kernel, Buildroot and Bootloader. In contrary of the script runme, i build the sdcard.img with buildroot and genimage. My problem were in the configuration of genimage. I have implanted directly the uboot. If it can helps someone, i can share the config of the genimage,as well as the config of buildroot. Thank again for your answers.